Seaboats Main > Commercial Vessels > Passenger Vessels > Ferries >

Island Class Bow Loading Car/Passenger Ferry



Listing ID:
1071

DESCRIPTION:Island Class Bow Loading Car Passenger
DATE LAUNCHED:1990
LENGTH:15m (50ft)
BEAM:13.5m (44ft 3in)
DRAFT:1.2m (4ft)
LOCATION:Somerset, UK
BROKER:Richard Pierrepont
PRICE:450,000
PRICE NOTES:Tax Exempt

Send Enquiry


General Description:

Please scroll down to view more photos

 
Description
100 Pax Island Class Bow Loading Car / Passenger Ferry For Sale
 
Length: 50ft
Beam: 20ft
Draft: 4ft
GRT: 42.50
Built: 1990
Re-built:  2012 Operating in the Bristol Channel UK
 
Steel construction, twin screw, brand new Perkins M185C 185hp less than 600hrs 3: 1-reduction PRM 1000 gearboxes, hull speed 8.5kts. She has recently undergone extensive refit. Ultrasonic tests show that her hull is on original 8.00mm & 6.25mm thickness. The main ramp is operated hydraulically. Current use is mainly for foot passengers so main deck seats can be hinged up giving vehicular access 11ft x 22ft.
 
The saloon has a toilet, a store/locker, small tuck shop and seating for 24 passengers, small aft deck and stairs up to bridge deck. On the bridge deck there is buoyant apparatus and seating for another 20 odd passengers. The wheelhouse is very spacious with AIS, Chart Plotter, GPS, Radar, depth sounder, wind speed and direction indicator, two VHF Radios and three hand-held Radios, the steering is hydraulic. The compass has not long been swung and the deviation card is in date. There is a chart table and the visibility from the wheel-house is excellent.
 
Existing MCA V1a certificate is for 100 passengers and no vehicles (summer) & class V1 year round 50 passengers and 1 vehicle. If deck seats removed then she should be able to go back to her old certification of 100 passengers no vehicles or 50 passengers and 1 vehicle or 25 passengers and two vehicles for short runs. This vessel was built so that she could easily be extended with an extra section welded in thus increasing her car capacity up to 4 or 6 cars. She would also be compliant for the work-boat code 60 miles offshore. 
 
Owner says: Our scope of work is changing and this vessel is under used on its present service, we are therefore testing the market. We were quoted around £1.2 Million to have one of these vessels built ten years ago a similar one has just been ordered for North Ireland at £2.8M we will consider offers in region of £525.000 
We have a 4.5 ton Tico deck crane that we never fitted, we had a special seat made for it but it would have cost us about 15-20 passengers so we left it off. We will include this along with two substantial extension ramps, these could be welded together to form an extension flap to the ramp if required but that would be for the next owner to sort out.
 
Specifications
Vessel type: Bow Loading Island Class Car/ Passenger Ferry
Designer: Strathclyde Maritime Design
Builder: McRindles
Model: Island Class Passenger/Car Ferry
Year constructed: 1990
Registry: UK
No. of engines: 2
Engine Model: Perking M185C
Engine power: 370
Engine hours: 450
Fuel type: Diesel
Drive type: shaft drive
Length overall: 15m
Beam: 19’
Maximum  Draft: 4’
Bridge clearance: 25’
Hull material: Steel
Hull Type: Displacement
Hull Colour: Black/ Red
Keel type: Full Keel
Displacement: 45 metric tons
Fuel capacity: 600 gallons
 
Engine(s)
In 2012-13 Brand new Perkins M185C engines were fitted and these have only just been run in with 450 hour on each at the time of writing. There is also a Lister TS2 9 Kva generator fitted which provides 240 volts power & lighting throughout the ship. this currently has 1200 hours on the clock.
Just before the new engines were delivered from Perkins the engine room was completely cleaned & ground back to bare metal where required and two coats of 2 pack Hempel epoxy coatings applied. The engine room floor plates were also taken out shot-blasted and sent off to be galvanised. We have just finished this treatment in all of her other compartments she is virtually now as in as good condition as when she left the builders yard.

The engines water feed pipes were also ripped out and new 316 stainless steel piping fitted. The new turbo charged engines also required larger diameter exhaust pipes so these too were ripped out and 316 stainless steel new ones fitted right up to the top of the funnel.
 
Construction
She is 'Clyde Built' of steel mostly in 8mm plate she has inch thick grounding plates welded to her keel and 2 inch grounding bars welded to her underside to help protect the hull during beaching/slipway operations. She was designed to be cut & extended if required. The bow ramp is operated hydraulically.
 
Accommodation
The accommodation is underneath the bridge and is heated by means of the exhaust pipes which are in a stainless steel meshed cage. There are seats and benches photos to follow:
 
Equipment
She has a jason's cradle for recovery of MOB, there are 100 buoyancy aids which are stowed under the seats. there are 10 life-rings and two buoyant apparatus. She also carries a 65 man self inflating life-raft and this is currently on hire from ADEC Marine.
Navigation Equipment
AIS, Garmin Radar/chart-plotter VHF radio plus three hand-helds.
 

Download as PDF



IMPORTANT: The Company offers the details of this vessel in good faith but cannot guarantee or warrant the accuracy of this information nor warrant the condition of the vessel. A buyer should instruct their agents, or their surveyors, to investigate such details as the buyer desires validated. This vessel is offered subject to prior sale, price change, or withdrawal without notice.

You are logged in:


Logout

facebook-button

TwitterButton

  Bookmark this page in your web browserwww.seaboats.net - HomeCartNo Items in your Cart